• Support
• Fireking Advantage
• Service Pyramid
• Marketing Materials
• Training / FireKing University
• Sales Team

• Office
• Convenience Store
• Restaurants
• Retailers
• Home Office
• Healthcare

• Files
• CCTV
• Safes
  • Dials
  • Keypads
  • Sherlock
  • Easy Series
  • AuditLok XL
    > XL Simulator
  • AuditLok XLV
    > XLV Simulator

AuditLok XL

Operation
Audit Report | Duress Feature | User Permissions | Simulator

Trouble
Alarm Sounding | Error Messages | Key Problems | Power Problems | Printing Problems

Tech Info
Alarm Wiring | Overrides | Parts List | Tech Updates

Major features of the AuditLok XL include a 5000 line audit trail, control of up to 4 safe doors, choice of keyed, keyless and biometrics access, and a very easy to use human interface that does not compromise security.

BSD Safe Literature
AuditLok XL Installation Setup Instructions
AuditLok XL Operator Manual
HUP80-31 Safe Power Supply
Offer: AuditLok XL Upgrade Offer!

Printing the Audit Report

^ back to top ^

Duress Feature

When

How

Note: It is strongly recommended that users avoid PINs that end with a "9". This is because adding a 1 rolls over the second digit as well, and in a duress situation it may be very difficult to enter the correct code for duress. If, for example, the PIN is 1459, the duress code would be 1460. Though only one number higher, this can be confusing under the conditions of duress.
 
^ back to top ^

User Permission Chart

*These functions may be performed via override.

<Simulate enrolling a new user>

^ back to top ^

Alarm Sounding

With Message "VIOLATION CLOSE DOOR"

With Message "BATTERY LOW" or With Screen Blanking Out

^ back to top ^

Error Messages

Message "ERROR, NOT A VALID KEY" Appears when Presenting Key

Message "ELECTRONICS ERROR"

Message "BATTERY LOW"

Message "VIOLATION CLOSE DOOR"

^ back to top ^

Key Problems

Key Does Not Perform Desired Function

Message "ERROR, NOT A VALID KEY" Appears when Presenting Key

Present Key, but No Response from Keypad

^ back to top ^

Loss of Power

Note: These additional steps apply to authorized service personel only:
4. If a volt-meter is available skip to Step 5. Check the transformer temperature. If it was plugged in correctly and the outlet had power, the transformer should be warm. If the transformer has a light it should be lit. If the transformer is cold or extremely hot replace the transformer. If in doubt and parts must be shipped anyway, send a transformer just in case.
5. Check transformer output voltage at the mouser connector (where the transformer cable plugs into the rear of the safe). If the output is bad, replace the transformer. If the output is good, it may be necessary to have the safe drilled open and replace the lock and the inner board. Replace other parts only if a new inner board does not solve the problem.
6. Before drilling removed the outer board and check the electrical connections to this board to ensure the problem is not simply a loose wire.

Parts Potentially Needed:

^ back to top ^

Problems Printing the Audit

Solution: When the printout gets close to the end of the "Key Data List", inner-board can hold up to 200 keys, press any button on the Keypad except escape, "ESC".

Why?: It is believed that this will slow down AuditLok XL enough for the printer buffer to catch up.

^ back to top ^

Alarm Wiring Data

For complete diagram info CLICK HERE.

DB15 D-Shell Connector Pin-Out:

Relay Specifications:

^ back to top ^

Overrides

Overrides may be performed to access any setup parameter. Most overrides require written authorization from corporate management. Charges may apply

TYPES OF OVERRIDES:
00 Lost Key (Simulate a key for up to 24 hours)
01 Edit Users (delete, activate, or deactivate an enrolled user)
02 Enroll User (Enroll a new keyed, keyless, or fingerprint user)
03 Date (Set the system date)
04 Time (Set the system time)
05 Idle Text (Set the name of the company to appear at idle)
06 Company Code (Set company specific code to control key access)
07 Door Configuration (Edit the door setup)
10 PIN Life (Control PIN expiration parameters)
11 Break Timelock (breaks timelock one time, must be used within 24 hours)
12 Set Delay/Timelock (Edit time delay and timelock settings for doors)

OVERRIDE PROCEDURE (XL Version 2.41)
1. Establish telephone contact with NKL Technical Service (1.800.452.4655). Be ready to talk and press buttons at the same time. Appropriate authorization may be required.
2. Press 1 and 4 simultaneously until COMPANY and SERIAL numbers appear on the screen.
3. Make sure no asterisks (* symbol) appear on the screen yet.
4. Enter the PIN 0000.
5. Enter the USER ID 888888888 and select DONE.
6. Read to the factory technician the 9-digit safe code displayed in the lower-left portion of the display.
7. Factory technician generates a response code and reads this code to you. You enter this code as it is being read to you. Pay no attention to the screen while entering the override number. WARNING: Once you begin entering the response code any pause of more than 7 seconds will exit you to the screen saver mode and you will have to begin again from step 1.
8. After correctly entering the last digit of the sequence the display will read FACTORY LOST KEY, PLEASE ENTER PIN. If the display reads anything different, press the arrow key in the upper right corner and repeat Step 7. If this happens twice, start over at Step 1.
9. Enter the PIN 0000.
10. Follow directions on the screen.

OVERRIDE PROCEDURE (XL Version 2.53 or higher Keyless/Bio Features)
1. Establish telephone contact with NKL Technical Service (1.800.452.4655). Be ready to talk and press buttons at the same time. Appropriate authorization may be required.
2. Press the bottom left scroll button twice. COMPANY and SERIAL numbers will appear on the screen.
3. Enter 0000.
4. Enter the USER ID 888888888 and select DONE.
5. Read to the factory technician the 9-digit safe code on the display.
6. Factory technician will generate a response code and read it to you. Enter this code as it is being read to you. WARNING: After entering the response code any pause of more than 7 seconds will exit you to the screen saver mode and you will have to begin again from step 1.
7. After correctly entering the last digit of the sequence the display will read FACTORY LOST KEY, PLEASE ENTER PIN. If the display reads anything different start over at Step 1.
8. Enter 0000.
9. Follow directions on the screen.

^ back to top ^

Parts List

^ back to top ^

Technical Updates

^ back to top ^